Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 605

Страница: 605 / 2589

Fig. 20: Jacking Up Rear Drive Shaft

Courtesy of MAZDA MOTORS CORP.

REAR DIFFERENTIAL DISASSEMBLY

1. Disassemble in the order indicated in the table.

WARNING:

The engine stand is equipped with a self-lock mechanism, however,

if the rear differential is in a tilted condition, the self-lock mechanism

could become inoperative. If the rear differential unexpectedly
rotates it could cause injury, therefore do not maintain the rear

differential in a tilted condition. When turning the rear differential,

grasp the rotation handle firmly.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLES Differential - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:52:15 AM

Page 12

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды