Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 702 | Manualshive

Страница: 702 / 2589

background image

Fig. 7: Identifying DSC/RSC HU/CM Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

DSC/RSC HU/CM CONNECTOR REMOVAL NOTE

1. Remove the DSC/RSC HU/CM connector using the following procedure:

1. Press down the lock lever while pressing the upper tab to release the lock.
2. Press down the lock lever and lock it using the lower tab.
3. Remove the DSC/RSC HU/CM connector by pulling it in the direction of the arrow.

Fig. 8: View Of DSC/RSC HU/CM Connector

Courtesy of MAZDA MOTORS CORP.

BRAKE PIPE REMOVAL NOTE

1. Place an alignment mark on the brake pipe and DSC/RSC HU/CM.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Dynamic Stability Control/Roll Stability Control - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:40:24 AM

Page 9

© 2005 Mitchell Repair Information Company, LLC.

«
...
700
701
702
703
704
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Metra Electronics Страницы: 14

Бренд: Vintage Air Страницы: 28

Car Top Duffle Bag

Бренд: Rightline Gear Страницы: 2

Бренд: Würth Страницы: 36

Бренд: Whispbar Страницы: 14

Бренд: Prorack Страницы: 15

Бренд: Webasto Страницы: 44

MAGICGRIP MGQDWD-CPO

Бренд: Scosche Страницы: 12

Бренд: Brodit Страницы: 2

Бренд: BMW Страницы: 177

Бренд: Volvo Страницы: 3

Бренд: Stack Страницы: 4

ActiveStart ACS30P

Бренд: Active Controls Страницы: 2

Бренд: Metra Electronics Страницы: 2

Бренд: Toyota Страницы: 4

Бренд: Toyota Страницы: 29

Бренд: Toyota Страницы: 36

Бренд: Toyota Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды