Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1912

Страница: 1912 / 2589

3. Remove the assist handle by shaking it up and down.

Fig. 78: Removing Assist Handle Bracket

Courtesy of MAZDA MOTORS CORP.

ASSIST HANDLE INSTALLATION

1. Push the assist handle in the direction of the arrow with the assist handle cover assembled to install the

assist handle.

Fig. 79: Pushing Assist Handle

Courtesy of MAZDA MOTORS CORP.

SUNVISOR REMOVAL/INSTALLATION

CAUTION:

When inserting a flathead screwdriver, be careful not to damage
the assist handle tabs shown in the figure.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 48

«
...
1910
1911
1912
1913
1914
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды