Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2065 | Manualshive

Страница: 2065 / 2589

background image

2008 ENGINE

Lubrication (MZI-3.7) - Mazda CX-9

LUBRICATION SYSTEM LOCATION INDEX [MZI-3.7]

Fig. 1: Identifying Lubrication Components

Courtesy of MAZDA MOTORS CORP.

ENGINE OIL LEVEL INSPECTION [MZI-3.7]

1. Position the vehicle on level ground.
2. Warm up the engine.
3. Stop the engine and allow

approx. 5 min

before continuing.

4. Remove the dipstick, wipe it clean, and reinstall it fully.
5. Remove the dipstick and verify that the oil level is between the L and F marks on the dipstick.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Lubrication (MZI-3.7) - Mazda CX-9

2008 Mazda CX-9 Grand Touring

2008 ENGINE Lubrication (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:14 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Microsoft

Sunday, November 15, 2009 10:01:18 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

«
...
2063
2064
2065
2066
2067
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: ZAPTEC Страницы: 240

Бренд: AAMP of America Страницы: 6

Бренд: Camcar Страницы: 6

LeisureWize EMOVE EM303A

Бренд: Streetwize Страницы: 20

Бренд: Warn Страницы: 5

Бренд: INDIWORK Страницы: 18

Бренд: Opel Страницы: 103

Бренд: Mercedes-Benz Страницы: 493

Бренд: AUTOTECH Страницы: 4

Бренд: iDataLink Страницы: 11

LockNLoad 9831007

Бренд: Yakima Страницы: 6

Бренд: Kuda Страницы: 3

Бренд: Dakota Digital Страницы: 2

Бренд: DV8 Страницы: 17

Бренд: Crux Страницы: 4

Бренд: travall Страницы: 3

ESCALADE EXT 2004

Бренд: Cadillac Страницы: 20

Бренд: BMW Страницы: 317

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды