Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 579

Страница: 579 / 2589

8. Refill the engine coolant. (See

ENGINE COOLANT REPLACEMENT [MZI-3.7]

9. Inspect for engine coolant leakage. (See

ENGINE COOLANT LEAKAGE INSPECTION [MZI-3.7]

10. Inspect the ATF level. (See

AUTOMATIC TRANSAXLE FLUID (ATF) INSPECTION [AW6A-EL,

AW6AX-EL]

Fig. 12: Identifying Coolant Reserve Tank Hose, Lower Radiator Hose, Oil Collar Water Hose And

Upper Mount Rubber Bracket

Courtesy of MAZDA MOTORS CORP.

UPPER MOUNT RUBBER BRACKET REMOVAL NOTE

CAUTION:

Do not apply force excessively and in the directions that are not

specified, otherwise the upper mount rubber bracket could be
damaged.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Cooling System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:57:25 AM

Page 13

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды