Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 70

Страница: 70 / 2589

DIAGNOSTIC PROCEDURE

DTC B1317, B1318 DIAGNOSTIC PROCEDURE

Step

Inspection

Action

INSPECT FUSE

Remove the SAS 7.5 A fuse.

Is the fuse normal?

Yes Go to the next step.

Replace the fuse.

INSPECT BATTERY

Measure the battery positive voltage.

Is the voltage

8 V-18 V?

Yes Go to the next step.

The battery has a malfunction.

Inspect the charge/discharge system.

INSPECT WIRING HARNESS BETWEEN
BATTERY AND FUSE BLOCK

Yes

Install the fuse, then go to the next
step.

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:18:47 AM

Page 70

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды