Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1530

Страница: 1530 / 2589

Fig. 50: Audio Control Switch Terminals Continuity Chart (With HF/TEL System)

Courtesy of MAZDA MOTORS CORP.

Fig. 51: Audio Control Switch Terminals Continuity Chart (With HF/TEL System)

Courtesy of MAZDA MOTORS CORP.

Fig. 52: Identifying Audio Control Switch Terminals (With HF/TEL System)

Courtesy of MAZDA MOTORS CORP.

R : Resistance. See the table.

RESISTANCE SPECIFICATION

MICROPHONE REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.

Switch position

Resistance (ohm)

VOL- button ON

51-56

VOL+ button ON

140-154

SEEK+ button ON

286-315

SEEK- button ON

534-589

MODE button ON

985-1,088

VOICE/MUTE button ON

1,935-2,138

OFF

4,795-5,299

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:06 AM

Page 30

«
...
1528
1529
1530
1531
1532
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды