Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2345

Страница: 2345 / 2589

WITH ADVANCED KEYLESS SYSTEM

Diagnostic procedure

DTC U0127 DIAGNOSTIC PROCEDURE

POSSIBLE CAUSE

terminal 3Q and the instrument cluster terminal 1N.

Keyless control module malfunction.

Instrument cluster malfunction.

Poor connection at connectors (female terminal)

With keyless entry system

Open or short circuit in the wiring harness between the keyless receiver

terminal D and the instrument cluster terminal 1N.

Keyless receiver malfunction.

Instrument cluster malfunction.

Poor connection at connectors (female terminal)

STEP

INSPECTION

ACTION

INSPECT WHEEL UNIT SIGNAL

FOR OPEN CIRCUIT

Turn the ignition switch off.

Disconnect keyless CM and
instrument cluster connectors.

Inspect for continuity between

keyless CM terminal 3Q
(harness-side) and instrument

cluster terminal 1N (harness-
side).

Is there continuity?

Yes Go to the next step.

Repair or replace the wiring harness for an open circuit

between keyless CM terminal 3Q and instrument

cluster terminal 1N, then go to Step 5.

INSPECT WHEEL UNIT SIGNAL
FOR SHORT TO POWER

Turn the ignition switch off.

Disconnect keyless CM and

instrument cluster connectors.

Measure the voltage between
keyless CM terminal 3Q

(harness-side) and ground.

Is there B+?

Yes

Repair or replace the wiring harness for a short to

power between keyless CM terminal 3Q and
instrument cluster terminal 1N, then go to Step 5.

Go to the next step.

INSPECT WHEEL UNIT SIGNAL

2008 Mazda CX-9 Grand Touring

2008 SUSPENSION On-Board Diagnostic (Suspension) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:25:36 AM

Page 13

«
...
2343
2344
2345
2346
2347
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды