Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2290

Страница: 2290 / 2589

POSITION MEMORY SWITCH INSPECTION

1. Disconnect the position memory switch connector.
2. Inspect for continuity between the power seat switch connector terminals.

If not as specified, replace the position memory switch.

Front tilt motor

power supply

Front tilt

motor

Front tilt motor stopped

1.0 or less

motor

Related wiring

harnesses

Front tilt motor
pulse

Front tilt
motor

Measure the waveform
while driving motor

operation using the
oscilloscope.

High
output: 4.8

or more

Front tilt

motor

Related wiring
harnesses

Low
output: 1.0

or less

Front tilt motor stopped

1.0 or less

or 5.0

Rear tilt motor
power supply

Rear tilt motor

Rear tilt motor moving

B+

Rear tilt motor

Related wiring

harnesses

Rear tilt motor stopped

1.0 or less

Rear tilt motor

pulse

Rear tilt motor

Measure the waveform
while driving motor

operation using the
oscilloscope.

High
output: 4.8

or more

Rear tilt motor

Related wiring
harnesses

Low

output: 1.0
or less

Rear tilt motor stopped

1.0 or less

or 5.0

Recliner motor

power supply

Recliner motor

Recliner motor moving

B+

Recliner
motor

Related wiring

harnesses

Recliner motor stopped

1.0 or less

Recliner motor

pulse

Recliner motor

Measure the waveform
while driving motor

operation using the
oscilloscope.

High
output: 4.8

or more

Recliner

motor

Related wiring

harnesses

Low

output: 1.0
or less

Recliner motor stopped

1.0 or less

or 5.0

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Seats - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:01 AM

Page 23

«
...
2288
2289
2290
2291
2292
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды