manualshive.com logo in svg

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Mazda CX-9 Grand Touring 2008 - роскошный семиместный кроссовер с высоким уровнем комфорта и мощным двигателем. Перед вами отличная возможность скачать бесплатно руководство пользователя для этой модели на manualshive.com. Получите свой экземпляр уже сегодня и ознакомьтесь с функциональностью автомобиля.

Поделиться
Скачать
background image

4. Third-row seat (See 

THIRD-ROW SEAT REMOVAL/INSTALLATION

 .)  

5. Third-row seat belt lower anchor installation bolt (See 

REAR SCUFF PLATE 

REMOVAL/INSTALLATION

 .)  

6. Rear scuff plate inner (See 

REAR SCUFF PLATE REMOVAL/INSTALLATION

 .)  

7. Trunk side trim (See 

TRUNK SIDE TRIM REMOVAL/INSTALLATION

 .)  

8. Second-row seat belt upper anchor installation bolt (See 

SECOND-ROW SEAT BELT 

REMOVAL/INSTALLATION

 .)  

9. Roof side trim (See 

ROOF SIDE TRIM REMOVAL/INSTALLATION

 .)  

10. C-pillar trim (See 

D-PILLAR TRIM REMOVAL/INSTALLATION

 .)  

11. Third-row seat belt upper anchor installation bolt (See 

REAR SCUFF PLATE 

REMOVAL/INSTALLATION

 .)  

12. D-pillar trim (See 

D-PILLAR TRIM REMOVAL/INSTALLATION

 .)  

2. Set the headliner out of the way.  
3. Apply protective tape along the edge of the body and the quarter window glass. 

Fig. 48: Applying Protective Tape Of Body

 

Courtesy of MAZDA MOTORS CORP.

 

NOT REUSING WINDSHIELD 

1. Cut out the sealant all around the glass from inside the vehicle using a sealant remover. 

2. Remove the quarter window glass. 

NOTE:

z

For the areas of the sealant that are difficult to cut, use the piano wire and 

follow the procedure under "Reusing Windshield".  

WARNING:

z

Using a razor with bare hands can cause injury. Always wear 

gloves when using a razor.  

 

2008 Mazda CX-9 Grand Touring 

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

  

Microsoft 

 

Sunday, November 15, 2009 10:36:16 AM

Page 35 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

FANATEC Porsche 911 Turbo S Wheel Developer Quick Manual preview
Porsche 911 Turbo S Wheel
Бренд: FANATEC Страницы: 9
HALE MM-03 Driver Manual preview
MM-03
Бренд: HALE Страницы: 44
Laser 4832 Manual preview
4832
Бренд: Laser Страницы: 8
PAC SWI-RC Installation Instructions preview
SWI-RC
Бренд: PAC Страницы: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Бренд: PAC Страницы: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Бренд: PAC Страницы: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Бренд: PAC Страницы: 5
Ultra Start KE-6 Owner'S Manual preview
KE-6
Бренд: Ultra Start Страницы: 8
Bestop WrapAround Windjammer Installation Instructions Manual preview
WrapAround Windjammer
Бренд: Bestop Страницы: 7
Opel 2011 Insignia Owner'S Manual preview
2011 Insignia
Бренд: Opel Страницы: 254
Xblitz Mirror 2016 User Manual preview
Mirror 2016
Бренд: Xblitz Страницы: 30
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Бренд: Lit Lightz Страницы: 3
Pet Gear TRI-FOLD PG9300RF Instruction Manual preview
TRI-FOLD PG9300RF
Бренд: Pet Gear Страницы: 4
POOL-LINE 110085 Assembly Instructions preview
110085
Бренд: POOL-LINE Страницы: 2
Jeep Grand Cherokee SRT 2019 Owner'S Manual preview
Grand Cherokee SRT 2019
Бренд: Jeep Страницы: 656
Westfalia 859528 Original Instructions Manual preview
859528
Бренд: Westfalia Страницы: 10
Webasto H300 comfort Operating Instructions Manual preview
H300 comfort
Бренд: Webasto Страницы: 44
Mercedes-Benz A 150 Owner'S Manual preview
A 150
Бренд: Mercedes-Benz Страницы: 305

Бренды по названию

Популярные бренды

Загрузить еще бренды