Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 355

Страница: 355 / 2589

6. Remove the control valve body. (See

CONTROL VALVE BODY REMOVAL/INSTALLATION

[AW6A-EL, AW6AX-EL]

7. Remove the input/turbine speed sensor.
8. Install the input/turbine speed sensor.

Tightening torque

3.9-6.9 N.m {40-70 kgf.cm, 26-60 in.lbf}

9. Install the control valve body. (See

CONTROL VALVE BODY REMOVAL/INSTALLATION

[AW6A-EL, AW6AX-EL]

10. Install the oil pipe. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

11. Install the oil cooler. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

Fig. 27: Locating Input/Turbine Speed Sensor

Courtesy of MAZDA MOTORS CORP.

12. Add ATF to the specified level. (See

AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT

CAUTION:

Do not damage the input/turbine speed sensor.

Fig. 26: Identifying Oil Cooler & Oil Pipe
Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 27

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды