Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2288

Страница: 2288 / 2589

Rear tilt switch

input (down)

Power seat

switch

Press the rear tilt switch to
down

1.0 or less

Power seat

switch

Related wiring

harness

Other

5.0

Recliner switch
input (forward)

Power seat
switch

Press the recliner switch to

forward

1.0 or less

Power seat

switch

Related wiring
harness

Other

5.0

Recliner switch

input
(backward)

Power seat
switch

Press the recliner switch to

backward

1.0 or less

Power seat

switch

Related wiring
harness

Other

5.0

Signal GND

input

Power seat

switch

Under any condition

1.0 or less

Power seat
switch

Related wiring

harness

Signal GND

input

Position

memory
switch

Under any condition

1.0 or less

Position
memory

switch

Related wiring
harness

Set switch input

Position

memory
switch

Press the set switch

1.0 or less

Position
memory

switch

Related wiring
harness

Other

5.0

Memory switch
1 input

Position
memory

switch

Press the memory switch 1 1.0 or less

Position

memory
switch

Related wiring

harness

Other

5.0

Memory switch

2 input

Position
memory

switch

Press the memory switch 2 1.0 or less

Position

memory
switch

Related wiring

harness

Other

5.0

Memory switch

3 input

Position

memory
switch

Press the memory switch 3 1.0 or less

Position
memory

switch

Related wiring
harness

Other

5.0

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Seats - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:01 AM

Page 21

«
...
2286
2287
2288
2289
2290
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды