Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 344

Страница: 344 / 2589

Fig. 9: Identifying Air Cleaner Component

Courtesy of MAZDA MOTORS CORP.

If there is any malfunction, perform an off-vehicle inspection of TFT sensor. (See

OFF-VEHICLE

INSPECTION

5. Install the TCM. (See

TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

6. Install the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

7. Connect the negative battery cable.

Fig. 10: Identifying Air Cleaner Component Connector Terminal

Courtesy of MAZDA MOTORS CORP.

OFF-VEHICLE INSPECTION

WARNING:

A hot transaxle and ATF can cause severe burns. Turn off the engine

and wait until they are cool before replacing the ATF.

CAUTION:

Water or foreign material entering the connector can cause a poor

connection or corrosion. Be sure not to allow water or foreign

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 16

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды