Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 2589

background image

4. Front console box (See

FRONT CONSOLE BOX REMOVAL/INSTALLATION

.)

5. Center panel (See

CENTER PANEL REMOVAL/INSTALLATION

.)

6. Front scuff plate inner (RH) (See

FRONT SCUFF PLATE REMOVAL/INSTALLATION

.)

7. Front side trim (RH) (See

FRONT SIDE TRIM REMOVAL/INSTALLATION

.)

8. Dashboard under cover (Passenger side) (See

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

.)

9. Glove compartment (See

GLOVE COMPARTMENT REMOVAL/INSTALLATION

.)

10. Side panel (See

SIDE PANEL REMOVAL/INSTALLATION

.)

11. Dashboard garnish (See

DASHBOARD GARNISH REMOVAL/INSTALLATION

.)

12. HF/TEL unit (See

HANDS-FREE TELEPHONE (HF/TEL) UNIT

REMOVAL/INSTALLATION

.) (vehicles with HF/TEL system)

4. Remove the bolts.
5. Remove the screws.
6. Remove the clips.
7. Remove the connector.
8. Remove the passenger-side air bag module in the direction of the arrow
9. Install in the reverse order of removal.

10. Turn the ignition switch to the ON position.
11. Verify that the air bag system warning light illuminates for

approx. 6 s

and goes out.

z

If the air bag system warning light does not operate normally, refer to the on-board diagnostic
system (air bag system) and perform inspection of the system. (See

FLOWCHART

.)

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS Air Bag System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:16:38 AM

Page 10

© 2005 Mitchell Repair Information Company, LLC.

«
...
100
101
102
103
104
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: UltraGauge Страницы: 55

Бренд: Yakima Страницы: 6

Бренд: Yakima Страницы: 18

Бренд: Metra Electronics Страницы: 2

Бренд: FORM FIT Страницы: 2

Бренд: Masterack Страницы: 4

Бренд: Over Armour Offroad Страницы: 5

Бренд: Sirius Satellite Radio Страницы: 8

Бренд: AA Products Страницы: 6

Бренд: METRON Страницы: 4

Бренд: NanoCam Plus Страницы: 32

Бренд: Velleman Страницы: 12

Бренд: Ford Страницы: 52

Бренд: Xingyun Страницы: 74

ESCALADE ESV 2005

Бренд: Cadillac Страницы: 482

Бренд: curt Страницы: 4

Бренд: Meritor Страницы: 20

SB-J-GCHER2/10W3v2

Бренд: Stealthbox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды