Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2431

Страница: 2431 / 2589

8. Install the rearview mirror.

Fig. 78: Identifying Ceramic Coating On Glass

Courtesy of MAZDA MOTORS CORP.

REARVIEW MIRROR REMOVAL [VEHICLES WITH AUTO LIGHT/WIPER

SYSTEM]

1. Insert a tape-wrapped flathead screwdriver into the notch and pry with the screwdriver in the direction

shown by the arrow to remove the covers.

Fig. 79: View Of Mirror Cover Notch

Courtesy of MAZDA MOTORS CORP.

2. Remove the covers.
3. Remove the rain sensor.(See

RAIN SENSOR REMOVAL/INSTALLATION

35°C {95°F}

Approx. 10 min

Approx. 2 h

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:17 AM

Page 52

«
...
2429
2430
2431
2432
2433
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды