Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2291

Страница: 2291 / 2589

Fig. 27: Position Memory Switch Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 28: Position Memory Switch - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

SEAT WARMER UNIT INSPECTION

SEAT CUSHION

1. Remove the front seat. (See

FRONT SEAT REMOVAL/INSTALLATION

2. Remove the seat cushion trim. (See

FRONT SEAT DISASSEMBLY/ASSEMBLY

3. While inspecting for continuity between the connector terminals A and B, use a dryer to warm the

thermostat of the seat warmer unit on seat cushion.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Seats - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:01 AM

Page 24

«
...
2289
2290
2291
2292
2293
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды