Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 349

Страница: 349 / 2589

Fig. 17: Identifying O-Ring & Gasket

Courtesy of MAZDA MOTORS CORP.

14. Install a new coupler component lock plate.
15. Install the control valve body. (See

CONTROL VALVE BODY REMOVAL/INSTALLATION

[AW6A-EL, AW6AX-EL]

16. Install the oil pipe. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

17. Install the oil cooler. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

18. Install the TCM. (See

TCM REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

19. Add ATF to the specified level. (See

AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT

[AW6A-EL, AW6AX-EL]

Fig. 18: Locating Coupler Component Lock Plate

Courtesy of MAZDA MOTORS CORP.

20. Install the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

21. Connect the negative battery cable.
22. Perform the mechanical system test. (See

MECHANICAL SYSTEM TEST [AW6A-EL, AW6AX-

EL]

INPUT/TURBINE SPEED SENSOR INSPECTION [AW6A-EL, AW6AX-EL]

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 21

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды