Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 685

Страница: 685 / 2589

Fig. 52: Crimping Boot Clamp With Clamp Pliers

Courtesy of MAZDA MOTORS CORP.

BOOT BAND (DIFFERENTIAL SIDE) DISASSEMBLY NOTE

1. Pry up the locking clips using a screwdriver.
2. Pull back the end of the band.

Fig. 53: Prying Locking Clips

Courtesy of MAZDA MOTORS CORP.

CLIP DISASSEMBLY NOTE

1. Mark the drive shaft and outer ring for proper assembly.

2. Remove the clip.

CAUTION:

Mark with paint; do not use a punch.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLES Drive Shaft - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:50:58 AM

Page 34

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды