Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2281

Страница: 2281 / 2589

Fig. 18: Recliner Motor - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

LUMBAR SUPPORT SWITCH INSPECTION

1. Disconnect the lumbar support switch connector.
2. Inspect for continuity between the lumbar support switch connector terminals.

If not as specified, replace the lumbar support switch.

Fig. 19: Lumbar Support Switch Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 20: Lumbar Support Switch - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

LUMBAR SUPPORT MOTOR INSPECTION

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Seats - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:01 AM

Page 14

«
...
2279
2280
2281
2282
2283
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды