Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 323

Страница: 323 / 2589

Fig. 295: Measuring Distance A Between End Of Torque Converter And End Of Converter
Housing

Courtesy of MAZDA MOTORS CORP.

103. Install the O-rings and oil pipes. (Refer to the appropriate article .)
104. Add the ATF.

AUTOMATIC TRANSAXLE INSPECTION

B2 Brake Inspection

1. Apply ATF to the driven plates, drive plates and retaining plates.

2. Install driven plates, drive plates and the retaining plate in the following order to the transaxle case as

shown in the figure.

Six drive plates type

Drive- Retaining- Driven- Drive- Driven- Drive- Driven- Drive- Driven- Drive- Driven- Drive-
Retaining

Seven drive plates type

Retaining- Drive- Driven- Drive- Driven- Drive- Driven- Drive- Driven- Drive- Driven- Drive-
Driven- Drive- Retaining

NOTE:

Replace with new drive plates after soaking them at least 2 h in ATF.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:18 AM

Page 160

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды