Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1417

Страница: 1417 / 2589

Fig. 5: Identifying Belt Length

Courtesy of MAZDA MOTORS CORP.

POWER STEERING OIL PUMP DRIVE BELT

1. Remove the generator and A/C drive belt. (See

GENERATOR AND A/C DRIVE BELT

2. Remove the power steering oil pump drive belt.

1. Install the

SST

between the power steering oil pump drive belt and the power steering oil pump

pulley.

NOTE:

Hold the SST by hand until it is lodges between the power

steering oil pump pulley and power steering oil pump drive belt.

Fig. 6: View Of SST Between Power Steering Oil Pump Drive

Belt & Power Steering Oil Pump Pulley

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:56 AM

Page 7

«
...
1415
1416
1417
1418
1419
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды