Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1687

Страница: 1687 / 2589

Fig. 11: Front Air Mix Actuator Operation Terminals A & E With E & C Resistance Graph -
Driver Side

Courtesy of MAZDA MOTORS CORP.

PASSENGER SIDE

1. Connect battery positive voltage to front air mix actuator terminal F (or G), connect terminal G (or F) to

ground, and then verify that the front air mix actuator operates as shown in the table.

If the operation condition is not normal, replace the front air mix actuator.

FRONT AIR MIX ACTUATOR OPERATION

Fig. 12: Front Air Mix Actuator Circuit Diagram - Passenger Side

Courtesy of MAZDA MOTORS CORP.

Terminal

Front air mix actuator operation

B+ Ground

COLD --> HOT

Ground B+

HOT --> COLD

2008 Mazda CX-9 Grand Touring

2008 HVAC Control System (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:12:35 AM

Page 8

«
...
1685
1686
1687
1688
1689
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды