Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1948

Страница: 1948 / 2589

AUTO LIGHT/WIPER CONTROL MODULE REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the dashboard under cover (Driver side). (See

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

(V)

IG 1

METER 10 A
fuse

Ignition switch at ON

B+

METER 10 A fuse

Related wiring harnesses

Ignition switch at LOCK

or ACC

1.0 or

less

Power

supply

BCM

ROOM
15 A

fuse

Constant

B+

BCM (See

BODY

CONTROL MODULE

(BCM) INSPECTION

Inspect ROOM 15 A fuse

Related wiring harnesses

TNS relay
operation

TNS relay

Light switch at low-
beam or high-beam

position

Below

1.5

TAIL 10 A fuse

TNS relay (See

RELAY

INSPECTION

Related wiring harnesses

Light switch at OFF

B+

H/L LOW
relay

operation

H/L LOW

relay

Light switch at high-

beam position

Below

1.5

H/L LOW relay (See

RELAY

INSPECTION

Related wiring harnesses

Light switch at OFF or

low-beam position

B+

TNS switch

on/off

Light switch

Ignition

switch at
ON

Light switch
at low-beam

or high-beam
position

1.0 or

less

Light switch (See

LIGHT SWITCH

INSPECTION

Related wiring harnesses

Light switch

at OFF

position

B+

Light

switch
on/off

Light switch

Ignition

switch at
ON

Light switch
at low-beam

or high-beam
position

1.0 or

less

Light switch (See

LIGHT SWITCH

INSPECTION

Related wiring harnesses

Light switch

at OFF
position

B+

GND

Under any condition

1.0 or

less

Related wiring harnesses

NOTE:

Auto light-off system are integrated with the auto light/wiper control
module.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 32

«
...
1946
1947
1948
1949
1950
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды