Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 401

Страница: 401 / 2589

17. Disconnect the manual valve link and remove the control valve body component.

Fig. 98: Locating Control Valve Body Component

Courtesy of MAZDA MOTORS CORP.

ON-VEHICLE INSTALLATION

1. Connect the manual valve link and install the control valve body component.

Fig. 97: Locating Control Valve Body Component
Courtesy of MAZDA MOTORS CORP.

CAUTION:

When installing the control valve body component, do not put the

coupler component in the open space of the separate plate in the

control valve body component.

Do not pinch the coupler component between the separate plate and
the control valve body component.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 73

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды