Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1870

Страница: 1870 / 2589

Fig. 4: Identifying Dashboard Component Removal Sequence & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

BOLT D REMOVAL NOTE

DASHBOARD REMOVAL NOTE

1. Raise the dashboard and detach the hooks from the body.

CAUTION:

Bolt D cannot be removed from the body. Due to this, bolt D could be
pinched when closing the front door, resulting in damage to the front

door. When closing the front door, verify that bolt D is completely
inserted

WARNING:

Removing the dashboard without supporting it can be dangerous.
The dashboard may fall and injure you. Always perform the following

procedure with at least another person.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:25 AM

Page 6

«
...
1868
1869
1870
1871
1872
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды