manualshive.com logo in svg

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Mazda CX-9 Grand Touring 2008 - роскошный семиместный кроссовер с высоким уровнем комфорта и мощным двигателем. Перед вами отличная возможность скачать бесплатно руководство пользователя для этой модели на manualshive.com. Получите свой экземпляр уже сегодня и ознакомьтесь с функциональностью автомобиля.

Поделиться
Скачать
background image

Fig. 16: Identifying Side Panel & Tab

 

Courtesy of MAZDA MOTORS CORP.

 

METER HOOD REMOVAL/INSTALLATION 

1. Remove the following parts: 

1. Decoration panel (See 

DECORATION PANEL REMOVAL/INSTALLATION

.)  

2. Front console box mat (See 

FRONT CONSOLE BOX MAT REMOVAL/INSTALLATION

.)  

3. Indicator panel (See 

INDICATOR PANEL REMOVAL/INSTALLATION

.)  

4. Front console box (See 

FRONT CONSOLE BOX REMOVAL/INSTALLATION

.)  

5. Center panel (See 

CENTER PANEL REMOVAL/INSTALLATION

.)  

6. Upper column cover (See 

COLUMN COVER REMOVAL/INSTALLATION

.)  

2. Detach clips A and pins B by pulling them in the direction of the arrow.  
3. Remove the meter hood.  
4. Install in the reverse order of removal. 

Fig. 17: Identifying Meter Hood & Clips

 

Courtesy of MAZDA MOTORS CORP.

 

GLOVE COMPARTMENT REMOVAL/INSTALLATION 

CAUTION:

z

If the glove compartment is closed without being joined to the stay 

 

2008 Mazda CX-9 Grand Touring 

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

  

Microsoft 

 

Sunday, November 15, 2009 10:43:26 AM

Page 14 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Feniex AM600 Instruction Manual preview
AM600
Бренд: Feniex Страницы: 6
Dakota Digital Retrotech RTX-68D-CHG Quick Start Manual preview
Retrotech RTX-68D-CHG
Бренд: Dakota Digital Страницы: 4
Ford FIESTA ST 2019 Supplement Manual preview
FIESTA ST 2019
Бренд: Ford Страницы: 37
Cadillac 2007 SRX Owner'S Manual preview
2007 SRX
Бренд: Cadillac Страницы: 522
Nuna Bugaboo turtle Instructions For Installation Manual preview
Bugaboo turtle
Бренд: Nuna Страницы: 17
Alpitronic Hypercharger HYC 075 Operation Instructions And Installation Manual preview
Hypercharger HYC 075
Бренд: Alpitronic Страницы: 64
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Бренд: Mercedes-Benz Страницы: 358
Metra Electronics 99-7477 Installation Instructions preview
99-7477
Бренд: Metra Electronics Страницы: 2
tams elektronik FCS-4 Manual preview
FCS-4
Бренд: tams elektronik Страницы: 19
Volvo 30661683 Installation Instructions, Accessories preview
30661683
Бренд: Volvo Страницы: 18
Chevrolet El Camino 1983 Owner'S Manual preview
El Camino 1983
Бренд: Chevrolet Страницы: 103
Peak PKC0BJ Owner'S Manual preview
PKC0BJ
Бренд: Peak Страницы: 8
Renault Kangoo Manual preview
Kangoo
Бренд: Renault Страницы: 239
Hollywood Racks HR4000 Assembly And Instruction Manual preview
HR4000
Бренд: Hollywood Racks Страницы: 8
Lexus 2014 GX 460 Quick Manual preview
2014 GX 460
Бренд: Lexus Страницы: 94
Mini Countryman Cooper S Owner'S Manual preview
Countryman Cooper S
Бренд: Mini Страницы: 244
Chevrolet 2003 Express Owner'S Manual preview
2003 Express
Бренд: Chevrolet Страницы: 402
PAC RadioPRO4 Manual preview
RadioPRO4
Бренд: PAC Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды