Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2337

Страница: 2337 / 2589

Fig. 5: Identifying DLC-2 Connector

Courtesy of MAZDA MOTORS CORP.

ACTIVE COMMAND MODES PROCEDURE

1. Connect the M-MDS to the DLC-2.
2. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

When using the IDS (laptop PC)

1. Select "DataLogger".
2. Select "Modules".
3. Select "IC".

When using the PDS (Pocket PC)

1. Select "Module Tests".
2. Select "IC".
3. Select "DataLogger".

NOTE:

The PID data screen function is used for monitoring the calculated

value of input/output signals in the module. Therefore, if the
monitored value of the output parts is not within the specification, it

is necessary to inspect the monitored value of input parts
corresponding to the applicable output part control. In addition,

because the system does not display an output part malfunction as

an abnormality in the monitored value, it is necessary to inspect the
output parts individually.

2008 Mazda CX-9 Grand Touring

2008 SUSPENSION On-Board Diagnostic (Suspension) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:25:36 AM

Page 5

«
...
2335
2336
2337
2338
2339
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды