Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 178

Страница: 178 / 2589

20. Disconnect the manual valve link and remove the control valve body component.

Fig. 23: Identifying Manual Valve Link

Courtesy of MAZDA MOTORS CORP.

21. Remove the coupler component lock plate.

22. Remove the coupler component from the transaxle case.

Fig. 22: Identifying Control Valve Body Bolts

Courtesy of MAZDA MOTORS CORP.

CAUTION:

Do not damage the wiring harness.

Do not pull hard on the wiring harness.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:15 AM

Page 15

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды