Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1565 | Manualshive

Страница: 1565 / 2589

background image

Fig. 27: Identifying Front Side Garnish With Clips

Courtesy of MAZDA MOTORS CORP.

REAR

1. Install clips A and then B to the vehicle from the rear side.

Fig. 28: Identifying Rear Side Garnish With Clips

Courtesy of MAZDA MOTORS CORP.

SIDE STEP MOLDING REMOVAL

1. Set the over fender out of the way
2. Remove the tow fasteners shown in the figure and set the front over fender out of the way.
3. Slide the side step molding in the direction of the arrow and detach clips A and B.
4. Remove the side step molding.
5. Remove clips A and B from the body, then install it to the side step molding.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Exterior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:03 AM

Page 20

© 2005 Mitchell Repair Information Company, LLC.

«
...
1563
1564
1565
1566
1567
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Dakota Digital Страницы: 2

Бренд: Dakota Digital Страницы: 7

Бренд: RaceChip Страницы: 12

Бренд: Jeep Страницы: 322

Бренд: Jeep Страницы: 341

Бренд: Jeep Страницы: 310

Бренд: Jeep Страницы: 189

Бренд: Jeep Страницы: 26

Бренд: Jeep Страницы: 21

Бренд: Vauxhall Страницы: 177

Бренд: Uebler Страницы: 18

Бренд: Suzuki Страницы: 353

Бренд: Torklift Страницы: 16

Sterling ALL-TERRAIN 576

Бренд: Roadmaster Страницы: 12

Бренд: Haibang Страницы: 6

WrapAround Windjammer

Бренд: Bestop Страницы: 7

PRIME DESIGN VRR-E-PM21

Бренд: Safe Fleet Страницы: 12

Бренд: Cadillac Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды