Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1888 | Manualshive

Страница: 1888 / 2589

background image

Fig. 34: Identifying Console Cover & Connector

Courtesy of MAZDA MOTORS CORP.

CONSOLE REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Decoration panel (See

DECORATION PANEL REMOVAL/INSTALLATION

.)

2. Front console box mat (See

FRONT CONSOLE BOX MAT REMOVAL/INSTALLATION

.)

3. Indicator panel (See

INDICATOR PANEL REMOVAL/INSTALLATION

.)

4. Front console box (See

FRONT CONSOLE BOX REMOVAL/INSTALLATION

.)

5. Dashboard under cover (See

DASHBOARD UNDER COVER REMOVAL/INSTALLATION

.)

6. Side wall (See

SIDE WALL REMOVAL/INSTALLATION

.)

7. Console panel (See

CONSOLE PANEL REMOVAL/INSTALLATION

.)

8. Console cover (See

CONSOLE COVER REMOVAL/INSTALLATION

.)

3. Remove the screws.
4. Remove the bolts.
5. Disconnect the accessory socket connector and auxiliary jack connector, and keyless antenna connector.
6. Remove the console in the direction of the arrow.
7. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 24

© 2005 Mitchell Repair Information Company, LLC.

«
...
1886
1887
1888
1889
1890
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Valeo Страницы: 17

Бренд: RACLET Страницы: 48

Бренд: RACLET Страницы: 31

Car Top Duffle Bag

Бренд: Rightline Gear Страницы: 2

Бренд: BMW Страницы: 55

Бренд: Whispbar Страницы: 15

Бренд: Honda Страницы: 20

2009 Rio Series

Бренд: Kia Страницы: 219

Бренд: Ecco Страницы: 12

Бренд: Brodit Страницы: 2

Бренд: Oldsmobile Страницы: 354

84 61 0 028 926

Бренд: BMW Страницы: 13

Бренд: Roadtrek Страницы: 61

Бренд: Webasto Страницы: 44

Бренд: Meritor Страницы: 20

SB-J-GCHER2/10W3v2

Бренд: Stealthbox Страницы: 2

Бренд: Volvo Страницы: 7

Бренд: Datsun Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды