Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1822

Страница: 1822 / 2589

CHECK CODE INSPECTION CHART (CHECK CODE 14)

Check code 16

CHECK CODE INSPECTION CHART (CHECK CODE 16)

Check code 22

CHECK CODE INSPECTION CHART (CHECK CODE 22)

Check code 14

Buzzer operation signal

INSPECTION CONDITION

DISPLAY

ACTION

After selecting check code 14, wait

for

approx. 2 s.

The buzzer

sounds.

The buzzer is normal.

The buzzer does

not sound.

Replace the

instrument cluster.

Check code 16

Fuel-level warning light flashing signal

INSPECTION

CONDITION

DISPLAY

ACTION

After selecting check code 16,
wait for

approx. 2 s.

Fuel-level warning
light flashes

three

times.

The fuel-level
warning light is

normal.

Except above

Replace the

instrument cluster.

Check code 22

Fuel level signal

STEP

INSPECTION CONDITION

DISPLAY

ACTION

Select check code 22 with the fuel gauge sender

unit connector disconnected.

Go to the next

step.

Except above

Go to the Step 6.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Instrumentation/Driver Info - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:42:27 AM

Page 12

«
...
1820
1821
1822
1823
1824
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды