Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1966

Страница: 1966 / 2589

Fig. 78: Inserting Screwdriver Into Service Hole

Courtesy of MAZDA MOTORS CORP.

VANITY MIRROR ILLUMINATION INSPECTION

1. Remove the sunvisor. (See

SUNVISOR REMOVAL/INSTALLATION

2. Verify that the continuity between the vanity mirror illumination terminals is as indicated in the table.

If not as indicated in the table, inspect the bulb. If there is no malfunction, replace the sunvisor.

Fig. 79: Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 80: Checking Continuity Between Vanity Mirror Illumination Terminals

Courtesy of MAZDA MOTORS CORP.

INDIRECT ILLUMINATION REMOVAL/INSTALLATION

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 50

«
...
1964
1965
1966
1967
1968
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды