Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1883 | Manualshive

Страница: 1883 / 2589

background image

Fig. 25: Identifying Inner Sail Garnish & Clip

Courtesy of MAZDA MOTORS CORP.

SIDE WALL REMOVAL/INSTALLATION

1. Remove the dashboard under cover (Driver side). (See

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

.)

2. Detach clips A and hook by pulling them in the direction of the arrow.
3. Remove the side wall.
4. Install in the reverse order of removal.

Fig. 26: Identifying Side Wall Hook & Clips

Courtesy of MAZDA MOTORS CORP.

DASHBOARD UNDER COVER REMOVAL/INSTALLATION

DRIVER SIDE

1. Remove the fasteners.
2. Detach tab A and hook by pulling them in the direction of the arrow.
3. Remove the dashboard under cover.
4. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 19

© 2005 Mitchell Repair Information Company, LLC.

«
...
1881
1882
1883
1884
1885
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Zavoli Страницы: 26

Бренд: FABBRI PORTATUTTO Страницы: 2

Бренд: MAXWORKS Страницы: 7

MagicWatch MWE250

Бренд: Waeco Страницы: 172

Бренд: Whispbar Страницы: 85

Бренд: iArmor Страницы: 4

Quantum Wash'n'Wipe N30208

Бренд: National Cycle Страницы: 12

Бренд: Metra Electronics Страницы: 20

3 Facelift 2006

Бренд: Mazda Страницы: 94

Бренд: Magneti Marelli Страницы: 3

Бренд: Metra Electronics Страницы: 12

Бренд: Scosche Страницы: 32

Бренд: Yakima Страницы: 10

Бренд: APS Страницы: 4

SKT 170 HYUNDAI

Бренд: Paser Страницы: 4

Бренд: Yakima Страницы: 13

Бренд: Volvo Страницы: 275

Electronic Levelling System

Бренд: E&P HYDRAULICS Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды