Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2280 | Manualshive

Страница: 2280 / 2589

background image

z

If not as specified, replace the slide adjuster.

Fig. 17: Slide Motor - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

RECLINER MOTOR INSPECTION

1. Disconnect the recliner motor connector.
2. Apply battery positive voltage to the recliner motor terminals and inspect the recliner motor operation

z

If not as specified, replace the slide adjuster.

MOTOR OPERATION

3. Connect the recliner motor connector.
4. Measure the recliner motor terminal C waveform during motor operation using the oscilloscope.

VOLTAGE SPECIFICATION

z

If not as specified, replace the slide adjuster.

Low output 1.0 or less

Motor operation

Connection

B+ GND

Forward

E

A

Backward

A

E

Condition Voltage (V)

High output 4.8 or more

Low output 1.0 or less

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Seats - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:01 AM

Page 13

© 2005 Mitchell Repair Information Company, LLC.

«
...
2278
2279
2280
2281
2282
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Ranger design Страницы: 6

Бренд: ABL Страницы: 176

Бренд: ABL Страницы: 94

Бренд: Xblitz Страницы: 30

Бренд: Oldsmobile Страницы: 2

Бренд: U.S. General Страницы: 8

Бренд: Subaru Страницы: 298

Бренд: Magneti Marelli Страницы: 2

Бренд: v.link Страницы: 19

Бренд: Kleinn Air Horns Страницы: 33

QuadraTop Adventure Top S

Бренд: Quadratec Страницы: 13

Бренд: TATA Motors Страницы: 146

Бренд: Yakima Страницы: 10

Бренд: Yakima Страницы: 12

Бренд: Adaptiv Mini Страницы: 4

Бренд: Prime Design Страницы: 16

Бренд: X-Armour Страницы: 16

ELECTRONIC SPEEDOMETER 1323

Бренд: VDO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды