Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1947

Страница: 1947 / 2589

Fig. 52: Identifying Auto Light-Off Control Module, Connector, Bolt & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

4. Install in the reverse order of removal.

AUTO LIGHT-OFF CONTROL MODULE INSPECTION

1. Measure the voltage at the auto light-off control module terminals as indicated below.

TERMINAL VOLTAGE LIST (REFERENCE)

Fig. 53: Identifying Auto Light-Off Control Module Connector Terminals

Courtesy of MAZDA MOTORS CORP.

CONNECTOR TERMINALS REFERENCE

Terminal

Signal

Connection

Test condition

Voltage

Action

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Lighting Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:39:06 AM

Page 31

«
...
1945
1946
1947
1948
1949
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды