Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2441

Страница: 2441 / 2589

Fig. 6: View Of Windshield Wiper Motor & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

BALL JOINT ASSEMBLY NOTE

1. Use a clean rag to protect the link, and squeeze using pliers.

Fig. 7: Identifying Ball Joint Assembly

Courtesy of MAZDA MOTORS CORP.

WINDSHIELD WIPER MOTOR ASSEMBLY NOTE

1. Connect the windshield wiper motor to the vehicle wiring harness connector, operate the windshield

wipers, and then stop them at the auto-stop position.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Wiper/Washer System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:35:19 AM

Page 6

«
...
2439
2440
2441
2442
2443
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды