Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 592 | Manualshive

Страница: 592 / 2589

background image

2008 ACCESSORIES & BODY, CAB

Cruise Control System (MZI-3.7) - Mazda CX-9

CRUISE CONTROL SWITCH INSPECTION [MZI-3.7]

1. Disconnect the negative battery cable.
2. Remove the driver-side air bag module. (See

DRIVER-SIDE AIR BAG MODULE

REMOVAL/INSTALLATION

.)

3. Disconnect the cruise control switch connector.
4. Inspect for resistance and continuity between the cruise control switch terminals using an ohmmeter.

z

If not as specified, replace the cruise control switch.

Fig. 1: Switch Position Chart

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Cruise Control System (MZI-3.7) - Mazda CX-9

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Cruise Control System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:48:51 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

Microsoft

Sunday, November 15, 2009 10:48:58 AM

Page 1

© 2005 Mitchell Repair Information Company, LLC.

«
...
590
591
592
593
594
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: ULTIMATE SPEED Страницы: 19

Бренд: HALE Страницы: 44

Бренд: Yakima Страницы: 4

Бренд: Victory 4x4 Страницы: 13

Бренд: SnapPad Страницы: 5

Chevrolet Silverado 2500HD 2021

Бренд: GMC Страницы: 433

Бренд: Harbor Freight Tools Страницы: 12

Бренд: Honda Страницы: 3

Бренд: Honda Страницы: 85

Бренд: v.link Страницы: 21

Бренд: Joie Страницы: 53

Бренд: POOL-LINE Страницы: 2

Бренд: Prorack Страницы: 15

Бренд: Enduro Страницы: 52

CHALLENGER HELLCAT 2017

Бренд: Dodge Страницы: 484

Бренд: Kargo Master Страницы: 7

Бренд: Brink Страницы: 12

Бренд: Mercedes-Benz Страницы: 357

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды