Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 364

Страница: 364 / 2589

Up switch

(Selector
lever

component)

Up switch

(Selector
lever

component)

Shift up (M range)

1.0

SELECTOR

LEVER

COMPONENT

INSPECTION

)

Inspect related

harness

Other ranges, all positions B+

Down switch
(Selector

lever
component)

Down switch
(Selector

lever
component)

Shift down (M range)

Below

1.0

Inspect selector lever
component (See

SELECTOR
LEVER

COMPONENT
INSPECTION

)

Inspect related

harness

Other ranges, all positions B+

Starter lock
output signal

PCM

Shift the

selector lever
to P or N

position.

Ignition

switch ON

B+

Inspect PCM

Inspect related
harness

Ignition
switch OFF

Below
1.0

CAN_L

PCM

Because this terminal is for

serial communication,
good/no good judgment by

terminal voltage is not
possible. Carry out

inspection according to
DTCs.

Inspect related

harness

M range
switch

M range

Below

1.0

Inspect selector lever

component (See

SELECTOR

LEVER
COMPONENT

INSPECTION

)

Inspect related
harness

Other positions, all ranges B+

A11

Power supply

Ignition
switch

Ignition switch ON

B+

Inspect Ignition

switch

Inspect related
harness

Ignition switch OFF

Below
1.0

A13

Back-up light
relay

Ignition
switch ON

Shift the

selector
lever to R

position.

Below

1.0

Inspect back-up light
relay (See

RELAY

INSPECTION

)

Inspect related
harness

Other

B+

Because this terminal is for

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 36

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды