Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1588

Страница: 1588 / 2589

Courtesy of MAZDA MOTORS CORP.

FRONT SHOCK ABSORBER AND COIL SPRING DISASSEMBLY/ASSEMBLY

1. Remove the front shock absorber and coil spring. (See

FRONT SHOCK ABSORBER AND COIL

SPRING REMOVAL/INSTALLATION

2. Disassemble in the order indicated in the table.
3. Assemble in the reverse order of disassemble.

Fig. 6: View Of Front Shock Absorber Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

PISTON ROD NUT DISASSEMBLY NOTE

WARNING:

Removing/installing the piston rod nut is dangerous. The shock

absorber and spring could fly off under tremendous pressure and

cause serious injury or death. Secure the shock absorber in the
SSTs before removing the piston rod nut.

2008 Mazda CX-9 Grand Touring

2008 SUSPENSION Front Suspension - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:23:19 AM

Page 4

«
...
1586
1587
1588
1589
1590
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды