Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2152

Страница: 2152 / 2589

DIAGNOSTIC PROCEDURE

DTC B2700 - DIAGNOSTIC PROCEDURE

DTC B2701 [POWER LIFTGATE (PLG) SYSTEM]

DTC B2701 - DETECTION CONDITION POSSIBLE CAUSE CHART

STEP

INSPECTION

ACTION

INSPECT PLG TOUCH SENSOR (RH)

Inspect the PLG touch sensor (RH).

(See

POWER LIFTGATE (PLG)

TOUCH SENSOR INSPECTION

Is the touch sensor normal?

Yes Go to the next step.

Replace the PLG touch sensor (RH).

(See

POWER LIFTGATE (PLG) TOUCH

SENSOR

REMOVAL/INSTALLATION

Go to Step 4.

INSPECT WIRING HARNESS BETWEEN

PLG CONTROL MODULE AND PLG
TOUCH SENSOR (RH)

Inspect the wiring harness between PLG
control module terminal 3A and PLG

touch sensor (RH) terminal B for an open
circuit/short circuit to power supply

system.

Is the wiring harness normal?

Yes Go to the next step.

Repair or replace the wiring harness.

Go to Step 4.

INSPECT WIRING HARNESS BETWEEN
PLG CONTROL MODULE AND PLG

TOUCH SENSOR (RH)

Inspect the wiring harness between PLG

control module terminal 2D and PLG
touch sensor (RH) terminal A for an open

circuit/short circuit to power supply
system.

Is the wiring harness normal?

Yes Go to the next step.

Repair or replace the wiring harness.

Go to the next step.

VERIFY CORRECTION COMPLETED

Reconnect the disconnected connector.

Clear the DTC.

Is DTC B2700 stored after

1 min or more

have elapsed?

Yes

Replace the PLG control module.

(See

POWER LIFTGATE (PLG)

CONTROL MODULE

REMOVAL/INSTALLATION

DTC troubleshooting completed.

DTC B2701

PLG touch sensor (LH) circuit malfunction

DETECTION

A short circuit to ground in the PLG touch sensor (LH) continues for 5 min or more

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES On-Board Diagnostic (Power Liftgate (PLG) System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:46:08 AM

Page 31

«
...
2150
2151
2152
2153
2154
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды