Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 354

Страница: 354 / 2589

[AW6A-EL, AW6AX-EL]

Fig. 25: Measuring Current Of Input/Turbine Speed Sensor

Courtesy of MAZDA MOTORS CORP.

12. Install the oil pipe. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

13. Install the oil cooler. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

14. Add ATF to the specified level. (See

AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT

[AW6A-EL, AW6AX-EL]

15. Install the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.7]

16. Connect the negative battery cable.
17. Perform the mechanical system test. (See

MECHANICAL SYSTEM TEST [AW6A-EL, AW6AX-

EL]

INPUT/TURBINE SPEED SENSOR REMOVAL/INSTALLATION [AW6A-EL,

AW6AX-EL]

1. Disconnect the negative battery cable.
2. Remove the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION

[MZI-3.7]

3. Drain the ATF. (See

AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT [AW6A-EL,

AW6AX-EL]

4. Remove the oil cooler.
5. Remove the oil pipe. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

WARNING:

A hot transaxle and ATF can cause severe burns. Turn off the engine

and wait until then are cool before replacing the ATF.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 26

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды