Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2297

Страница: 2297 / 2589

Fig. 39: Identifying Edge Cover And Long Slider Cover

Courtesy of MAZDA MOTORS CORP.

4. Remove the following parts:

1. Trunk box (See

TRUNK BOX REMOVAL/INSTALLATION

2. Seat side box (See

SEAT SIDE BOX REMOVAL/INSTALLATION

3. Trunk end trim (See

TRUNK END TRIM REMOVAL/INSTALLATION

4. Third-row seat (See

THIRD-ROW SEAT REMOVAL/INSTALLATION

5. Rear scuff plate inner (See

REAR SCUFF PLATE REMOVAL/INSTALLATION

6. Third-row seat belt lower anchor installation bolt (See

THIRD-ROW SEAT BELT

REMOVAL/INSTALLATION

7. Trunk side trim (See

TRUNK SIDE TRIM REMOVAL/INSTALLATION

5. Set the floor covering out of the way.
6. Remove in the order indicated in the table.

Fig. 40: Identifying Long Slider, Bolt & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

7. Install in the reverse order of removal.

THIRD-ROW SEAT REMOVAL/INSTALLATION

1. Remove the trunk box. (See

TRUNK BOX REMOVAL/INSTALLATION

2. Remove the covers.
3. Remove the bolts.
4. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Seats - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:01 AM

Page 30

«
...
2295
2296
2297
2298
2299
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды