Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1457

Страница: 1457 / 2589

Fig. 70: Identifying Cylinder Head Cover Bolts Tightening Sequence (RH)

Courtesy of MAZDA MOTORS CORP.

Tightening torque

8.5-11.5 N.m {87-117 kgf.cm, 76-101 in.lbf}

CAUTION:

Install the cylinder head cover installation bolt and studs within
5 min of applying the silicone sealant.

Fig. 69: Applying Silicone Sealant To Mating Faces (LH)
Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Mechanical (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:01:57 AM

Page 47

«
...
1455
1456
1457
1458
1459
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды