Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 146

Страница: 146 / 2589

2008 DRIVELINE/AXLE

All Wheel Drive (AWD) - Mazda CX-9

ELECTRONIC AWD CONTROL SYSTEM LOCATION INDEX

Fig. 1: Identifying Wheel Drive Components (AWD)

Courtesy of MAZDA MOTORS CORP.

AWD CONTROL MODULE INSPECTION

1. Measure voltage or resistance at each AWD CM terminal using a voltmeter and an ohmmeter.

If not as specified, replace the AWD CM.

TERMINAL VOLTAGE LIST (REFERENCE)

NOTE:

AWD CM terminal voltage can vary depending on measuring conditions

and vehicle aging, resulting in misdiagnosis. Therefore, it is necessary to
perform an overall inspection of the input/output systems and AWD CM to

determine which part is malfunctioning.

With the AWD CM connector connected, measure voltage by connecting

the voltmeter negative (-) lead to the body ground and positive (+) lead to
each AWD CM terminal.

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE All Wheel Drive (AWD) - Mazda CX-9

2008 Mazda CX-9 Grand Touring

2008 DRIVELINE/AXLE All Wheel Drive (AWD) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:31:22 AM

Page 1

Microsoft

Sunday, November 15, 2009 10:31:26 AM

Page 1

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды