Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 62

Страница: 62 / 2589

DIAGNOSTIC PROCEDURE

DTC B105B, B110C, B1144, B1145 DIAGNOSTIC PROCEDURE

STEP

INSPECTION

ACTION

INSPECT DRIVER-SIDE SIDE AIR BAG

SENSOR NO.2 CONNECTOR

Turn the ignition switch to the LOCK position.

Disconnect the negative battery cable and wait

for

1 min or more.

Disconnect the driver-side side air bag sensor
No.2 connector. (See

SIDE AIR BAG

SENSOR NO. 2
REMOVAL/INSTALLATION

Is there any malfunction of the driver-side side

WARNING:

Handling the air bag system components

improperly can accidentally deploy the air
bag modules and pre-tensioner seat belts,

which may seriously injure you. Read the
service warnings and cautions before

handling the air bag system components.

(See AIR BAG SYSTEM SERVICE

WARNINGS .)

(See AIR BAG SYSTEM SERVICE

CAUTIONS .)

Yes Replace the air bag wiring harness.

Go to the next step.

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:18:47 AM

Page 62

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды