Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1529

Страница: 1529 / 2589

Courtesy of MAZDA MOTORS CORP.

R : Resistance. See the table.

RESISTANCE SPECIFICATION

Fig. 49: Identifying Audio Control Switch Terminals (Without HF/TEL System)

Courtesy of MAZDA MOTORS CORP.

WITH HF/TEL SYSTEM

1. Verify the resistance and continuity between the audio control switch terminals.

If the resistance and continuity are not as indicated in the tables, replace the audio control switch.

HF/TEL SWITCH

Switch position

Resistance (ohm)

VOL- button ON

51-56

VOL+ button ON

140-154

SEEK+ button ON

286-315

SEEK- button ON

534-589

MODE button ON

985-1,088

VOICE/MUTE button ON

1,935-2,138

OFF

4,795-5,299

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:06 AM

Page 29

«
...
1527
1528
1529
1530
1531
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды