Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 32

Страница: 32 / 2589

DIAGNOSTIC PROCEDURE

DTC B104B, B104E, B1051, U2017 DIAGNOSTIC PROCEDURE

DETECTION

CONDITION

Malfunction in wiring harness between driver-side side air bag sensor No.1 and SAS

control module

Malfunction in driver-side side air bag sensor No.1 circuit

performing an inspection, always follow the inspection procedure.

POSSIBLE

CAUSE

Open or short circuit in wiring harness between driver-side side air bag sensor No.1

and SAS control module

Driver-side side air bag sensor No.1 malfunction

SAS control module malfunction

STEP

INSPECTION

ACTION

INSPECT DRIVER-SIDE SIDE AIR BAG

SENSOR NO.1 CONNECTOR

WARNING:

Handling the air bag system components
improperly can accidentally deploy the air

bag modules and pre-tensioner seat belts,
which may seriously injure you. Read the

service warnings and cautions before
handling the air bag system components.

(See AIR BAG SYSTEM SERVICE

WARNINGS .)

Yes Replace the air bag wiring harness.

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS On-Board Diagnostic (Restraints) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:18:46 AM

Page 32

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды