Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1571

Страница: 1571 / 2589

3. Peel off the backing paper and attach the door sash film onto the door as shown in the figure.

Fig. 37: Attaching Door Sash Film Onto Door

Courtesy of MAZDA MOTORS CORP.

Standard clearance

a: 2.0 mm or more {0.08 in or more}

b: 3.0-5.0 mm {0.12-0.19 in}

4. Peel off the transparent protective film on the door sash film.
5. Install the following parts:

1. Rear door garnish (See

REAR DOOR GARNISH REMOVAL/INSTALLATION

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Exterior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:03 AM

Page 26

«
...
1569
1570
1571
1572
1573
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды