Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1882 | Manualshive

Страница: 1882 / 2589

background image

Fig. 23: Identifying Ventilator Grille & Center Panel With Screw - Center

Courtesy of MAZDA MOTORS CORP.

REAR

1. Disconnect the negative battery cable.
2. Remove the console cover. (See

CONSOLE COVER REMOVAL/INSTALLATION

.)

3. Remove the rear cooler duct. (See

REAR COOLER DUCT REMOVAL/INSTALLATION

.)

4. Detach the pins A while holding the console cover.
5. Remove the ventilator grille in the direction of the arrow.
6. Install in the reverse order of removal.

Fig. 24: Identifying Ventilator Grille & Center Panel With Screw - Rear

Courtesy of MAZDA MOTORS CORP.

INNER SAIL GARNISH REMOVAL/INSTALLATION

1. Pull the sail garnish outward, then detach clips A.
2. Remove the inner sail garnish.
3. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 18

© 2005 Mitchell Repair Information Company, LLC.

«
...
1880
1881
1882
1883
1884
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

UNIVERSAL CJ-2A

Бренд: Jeep Страницы: 27

Бренд: Jeep Страницы: 228

Бренд: Jeep Страницы: 108

Бренд: Jeep Страницы: 525

HOIST-A-TOP JL CRANK

Бренд: Lange Originals Страницы: 13

Бренд: OEM Tools Страницы: 4

Бренд: Westin Страницы: 3

Бренд: Ford Страницы: 2

CHASSIS CAB 3500 2017

Бренд: RAM Страницы: 16

Бренд: Porsche Страницы: 195

PERFECTVIEW CAM80AHD

Бренд: Dometic Страницы: 196

Бренд: Honda Страницы: 208

Бренд: Kuda Страницы: 3

Бренд: Fab Fours Страницы: 19

Бренд: JKS Страницы: 3

Бренд: Yakima Страницы: 12

Бренд: Hama Страницы: 13

Бренд: Whispbar Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды