Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 647

Страница: 647 / 2589

Fig. 21: PLG Touch Sensor - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

POWER LIFTGATE (PLG) FRONT SWITCH REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the dashboard under cover. (Driver's side) (See

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

3. Remove the hood release lever. (See

HOOD LATCH AND RELEASE LEVER

REMOVAL/INSTALLATION

4. Remove in the order indicated in the table.

Fig. 22: Identifying PLG Front Switch & Connector

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

POWER LIFTGATE (PLG) FRONT SWITCH INSPECTION

1. Verify that the continuity between the PLG front switch terminals is as indicated in the table.

If not as indicated in the table, replace the PLG front switch.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Doors and Liftgate - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:45:23 AM

Page 21

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды